Concrobium Mould Control Product Application

Concrobium Mould Control is ideal for mould remediation in homes & offices & assists with mould prevention

Concrobium Mould Control dries on surfaces to create an invisible antimicrobial shield that kills and prevents mould, and gets rid of musty odours.

The breakthrough solution contains no bleach, ammonia, alcohol or other VOCs and is suitable for use on almost any surface.

Concrobium Mould Control is ideal for:

  • Remediation in homes, businesses and institutions
  • Mould prevention following flooding or water damage clean-up
  • Pre-treatment of building materials
  • Concrobium Mould Control can be used in homes, businesses, institutions, cottages, RVs, boats – anywhere that mould takes hold.
  • General interior maintenance – bathtubs, bathroom tiles, countertops, shower stalls, laundry rooms, walls, ceilings, around windows; musty basements, crawlspaces, roof spaces
  • Disaster restoration – mould remediation and prevention following flooding and leaks
  • Construction and renovation – pre-treatment of building materials (e.g. plaster, timber) for prevention; elimination of growth found during renovation
  • Specialty clean-up and prevention – Cars, RVs, boats, sporting equipment
    For use on finished and unfinished surfaces including: timber, plaster, concrete, siding, composite decking, metal, marble, tile, grout, fabric, upholstery, furniture, clothing

 

Directions for use:

Concrobium Mould Control can be used to clean and eliminate existing problems, and/or to prevent  growth in vulnerable areas. In conjunction with using this product, it is highly recommended that the conditions favourable to growth (excess water, humidity) be identified and corrected.

The product can be applied by a variety of application methods including hand-spray, paintbrush, roller, immersion, compression sprayer or cold (ULV) fogger (for more detailed fogging instructions please consult the final section of this document).  In all cases, the goal is to achieve a thin, even application on the surface, which must then be allowed to dry.

As Concrobium Mould Control dries on mouldy surfaces, it forms a hard polymer that physically crushes the micro-organisms underneath. That same polymeric barrier stays on surfaces to provide continual resistance against growth.

Coverage varies according to surface and application method.

Expect reduced coverage on absorbent surfaces such as fabrics, carpet, timber and unpainted plaster.

Do not dilute. Do not rinse. Do not use bleach-based products in combination as this may reduce product efficiency.

No special controls, ventilation, or personal protective equipment is required while handling the product. However, to avoid applicator exposure to mould or spores during use, consult product label section: “Personal Protection Equipment Requirements for Applicators”.

 

Preventative Treatment

  1.  Apply Concrobium Mould Control on area until evenly wet.
  2.  Allow treated surfaces to dry completely

 

To maintain protection against re-growth, do not rinse or wash surfaces after Concrobium treatment. A thin, even layer of the product should remain on surfaces to prevent spore attachment. If surface is subsequently painted or coated with another substance, reapply Concrobium.

Materials vulnerable to water marks should be wiped immediately after contact with Concrobium Mould Control. Over-application may in some cases result in residue formation, which can be easily wiped away with a dampened cloth.

 

Remedial Treatment

Areas of visible growth of less than 30 square feet (the area of a single wall panel) can normally be remediated without elaborate procedures. Areas larger than 30 square feet often require special procedures and individuals trained in remediation.

When mouldy areas are identified, apply Concrobium Mould Control to eliminate existing growth and prevent the spread of fungal spores.  If growth is on ceiling tiles or other such easily removable items of nominal value, consider removal and disposal of those items. 

If the surface is not easily replaceable:

  1. Apply Concrobium on affected area until evenly wet.
  2. Allow treated surfaces to dry completely.
  3. Clean any remaining stains and residue with a Concrobium-dampened cloth or brush.

 

Reapplication

Reapplication of Concrobium Mould Control may be required if surfaces are washed or painted or are otherwise directly exposed to excessive water or rinsing.  Surfaces that stay relatively dry and clean will remain continuously mould-resistant.

 

Personal Protection Equipment Requirements for Applicators

For areas less than 30 sq. feet, an N-95 respirator, gloves and goggles/eye protection are recommended to avoid exposure. For areas greater than 30 sq. feet, an N-95 respirator or half-face respirator with HEPA filter, disposable overalls, gloves and goggles/eye protection.

 

Concrobium Mould Control Fogging Instructions

 

Why Use a Fogger?
A fogger atomizes Concrobium Mould Control into a fine mist that quickly and evenly coats surfaces.

Fogging is ideal for treating and pre-treating various surfaces:

  • Large spaces e.g., entire rooms, basements, cellars
  • Hard-to-reach areas e.g., roof spaces, crawlspaces
  • Building materials e.g., plaster, flooring, ceiling tiles, wood, concrete
  • New home, building or institution construction sites e.g., framed house

 

General Fogging Directions
Fogging Objective: to saturate air with Concrobium Mould Control fog such that the product spreads throughout the target area and coats surfaces with a thin, even layer. Using the fogger as a sprayer to apply the product directly to surfaces may lead to over-application, which is not recommended.

  1. Review Table 1 for approximate fogging time and product required.
  2. Remove Fogger power head from tank. Add Concrobium Mould Control to fogger tank. Fasten clamps to secure power head.
  3. Install intake air filter to help protect motor from spores and moisture in intake air.  Intake filter installs over the louvers of rear housing of fogger. Attach the two adhesive backed hook fasteners to 10 and 2 o’clock positions, anchor bottom of filter and stretch elastic over housing. Filters can be cleaned and reused should they become soiled.
  4. Remove or cover any room contents that may be damaged if wetted e.g., furniture, electronics, electrical sources, paper products
  5. Adjust liquid flow rate knob at side of fogger head (Low, Med, High). The liquid flow rate determines the size of the fog droplets formed by the machine. A Medium flow rate is recommended for application of Concrobium Mould Control.
  6. Position and activate fogger in space being treated to ensure that a mist is created that fills the space. Adjust fogger head angle as required to ensure appropriate throw of fogged product. Fog target space according to fogging time recommendations in Table 1.
  7.  Do not over-apply product on surfaces. Run-off and pooling is a sign of over-application.
  8. When fogging is complete, open reservoir, remove suction tube from liquid source and operate fogger for one minute with flow rate set at high. This will remove remaining liquid from fogger’s internal lines.
  9. After fogging, allow fog to dissipate for 15-20 minutes. Where possible, wipe off any excess wetness from surfaces, particularly flat, horizontal ones, with a clean cloth.
  10. After fog has dissipated for required time, open windows and/or ventilate area to allow air exchange.
  11. Allow surfaces to dry overnight. Do not rinse. It may be necessary to wipe some surfaces clean after drying e.g., glass and mirrors.

 

Room Fogging Tips

  1. If fogging an entire room, fogger should be placed in middle of room – about 4’ off floor, for 8’ ceilings and 6’, for 10’ ceilings – adjust height for higher ceilings.  Aim fogger towards join line between ceiling and wall. 
  2. Start fogging on medium flow rate.  Rotate fogger continuously to ensure an even fog (eg: a quarter turn every two minutes). More frequent rotation or adjustments to the flow rate may be required if run-off or pooling develops.

 

NOTE:  Each area requires its own treatment considerations re product quantity, application duration, fogger positioning and rotation technique. It may be necessary to apply product for a longer period, in certain directions, to compensate for room dimensions eg: a long narrow room.  Fogger radius during treatment is 30 feet; it will be necessary to re-position fogger for rooms with dimensions greater than this. Mounting the fogger on a self-rotating turntable is a good way to achieve even application.

 

Table 1
*Area assumes surface coverage of all walls, floors and ceilings.
**Allow more time for rooms with higher ceilings

 

Fogger Operation Guidelines

  1. Use only a cold (ULV) fogger to fog Concrobium Mould Control. Do not use thermal foggers.
  2. Use only Concrobium Mould Control with your fogging machine. Do not apply any liquid that is hazardous to people, animals or property when atomized into small droplets.
  3. Avoid over-exposure to fog output. While Concrobium Mould Control contains no bleach, ammonia, alcohol, acids or VOCs, highly atomized droplets can float in the air a long time and are quickly absorbed by the lungs.  Avoid spending undue time in the target area until the fog has dissipated.
  4. Keep an intake air filter in place during use. This will help prevent dust and fog droplets from entering the unit. Air filters are multiple-use and can be cleaned with water and then dried.
  5. Use only a properly grounded (earthed) three pin electric outlet. The ground wire is an essential safety feature of this product. Do not remove the grounding lug on the power cord. Do not use an ungrounded (3”-to-2”) plug adapter.
  6. An extension cord, if used, must have a continuous ground wire leading to earth.
    The amperage rating of an extension cord, if used, must be greater than the amperage shown on the fogger nameplate label. Do not chain two extension cords together.

 

Moisture Cure (R) home page